AirTAC Standard Cylinder SU50X200

Ordering Code:

Specification:

Bore size		32	40	50	63	80	100
Acting type		Double acting
Fluid		Air ( to be filtered by 40 µm filter element)
Mounting type	SU	Basic FA   FB   CA   CB   LB   TC   TCM1
	SUD SUJ	Basic FA    LB   TC   TCM1
Operating pressure		0/15~1.0 MPa ( 22~145 psi) ( 1.5~10.0 bar)
Proof pressure		1.5 MPa ( 215 psi)(15 bar)
Temperature		-20~70
Speed range mm/s		30~800
Stroke tolerance		0~250            25~1000              1001~1500
Cushion type		Variable cushion
Adjustable cushion stroke		21				28	29
Port size①		1/8”	1/4”		3/8”		1/2”

• NOTE: ①PT thread, G thread and NPT thread are available.

Stroke:

Bore size (mm)	Standard stroke (mm)	Max.std stroke	Max. stroke
32	25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500	1000	2000
40	25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000	1200	2000
50	25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000	1200	2000
63	25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000	1500	2000
80	25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000	1500	2000
100	25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000	1500	2000

Note: If the stroke is ≥1600mm within the maximum strike scope, it is treated as non-standard one. Please contact us for other special stroke.

Product Feature:

1. Standard cylinder manufactured by our enterprise.
2. The seal of piston adopts heterogeneous two way seal structure. It’s dimension is tight and it has the function of grease reservation.
3. It is tie rod cylinder. The cylinder barrel and front/ rear cap is jointed by tie rods with high reliability.
4. Compared with ISO15552 standard cylinder, SU series cylinder with the same bore size is shorter.
5. The buffer adjustment of cylinder is smooth and steady.
6. Cylinders and mounting accessories with several specifications are optional.
7. The seal material with high temperature resistance is adopted to guarantee the normal operation of cylinder at 150℃.

Installation& Usage:

1. When load changes in the work, the cylinder with abundant output capacity shall be added.
2. Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.
3. Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.
4. Dirty substances in the pipe must be eliminated before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.
5. The medium used by cylinder shall be filtered to 40μm or below.
6. Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.
7. The cylinder shall be carried out test run without load before application. Prior to run, buffer shall be turned to the minimum and gradually released to avoid the damage on cylinder caused by excessive impact.
8. The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.
9. If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the surface. Anti-dust caps shall be added in air inlet and outlet ports.