Fluke 772 Milliamp Process Clamp Meter
Introduction:
This manual tells you about verification and adjustment procedures for the 772/773 Milliamp Process Clamp Meter (referred to in this manual as the Meter). The Meter features closed-case calibration to use with reference sources. It measures the reference signals, calculates the correction factors, and keeps them in memory. Calibration adjustment is required after a repair, or if the Meter fails a performance test.
Features:
- In-circuit measurement of 0-24 mA dc and up to 99.9 mA dc using a remotely connected clamp via extension cable
- 0-24 mA dc sourcing and simulating
- 0-10 V dc sourcing
- Loop power supply 24 V dc output
- 0-30 V dc measurement
- Scaled mA output
- Simultaneous mA measurement via detachable clamp and mA sourcing
- 250 Ω HART resistor for mA source
- Electronic zero
- Percentage span (0-100 %)
- Hold
- Auto power off (battery saver)
- Display backlight
- Measurement spotlight LED
| Technical specifications | |||||
| Range | Resolution | Accuracy | |||
| AC current Via Jaw | 0-20.99 mA; 21-100mA | 0.01Ma; 0.1 mA | 0.2 % ± 5 counts
1 % ± 5 counts |
||
| In Circuit | 0-24 mA | 0.01 mA | 0.2 % + 2 counts | ||
| Current Source | 0-24 mA | 0.01 mA | 0.2 % + 2 counts | ||
| mA Drive | 24 mA into 1000 Ω | ||||
| AC voltage | 600 V/1000V | 0.1 V/1V | 1.5 % ± 5 digits (20-500 Hz) | ||
| DC voltage | 600 V/1000V | 0.1 V/1V | 1 % ± 5 digits | ||
| Frequency Via Jaw | 5.0-500.0Hz | 0.1Hz | 0.5 % ± 5 digits | ||
| Trigger Level | 5-10 Hz, ≥10A
10-100 Hz, ≥5A 100-500 Hz, ≥10A |
||||
| Frequency Via Flexible Current Probe | 5.0-500.0Hz | 0.1Hz | 0.5 % ± 5 digits | ||
| Trigger Level | 5-20 Hz, ≥25A
20-100 Hz, ≥20A 100-500 Hz, ≥25A |
||||
| Resistance | 600/6000Ω/60kΩ | 0.1/1Ω/10Ω | 1 % ± 5 digits | ||
| General Specifications | |||||
| Size (LxWxH) | 277 mm × 88 mm × 43mm | ||||
| Jaw opening | 34 mm | ||||
| Weight | 350 g | ||||
| Flexible Current Probe Diameter | 7.5mm | ||||
| Flexible Current Probe Cable Length | 1.8m | ||||
| Safety rating | CAT III 600 V | ||||
| Warranty | 2 years | ||||
| Mechanical Specifications | |||||
| Batteries | 2 AA, NEDA 15A, IEC LR6 | ||||
| Operating temperature | -10 °C to +50 °C | ||||
| Storage temperature | -40 °C to +60 °C | ||||
| Operating humidity – non-condensing (< 10°C) |
≤90% RH (at 10 °C to 30 °C) | ||||
| ≤75% RH (at 30 °C to 40 °C) | |||||
| ≤45% RH (at 40 °C to 50 °C) | |||||
| Operating altitude | 2000 m | ||||
| Storage altitude | 12,000 m | ||||
Include:
- Four AA alkaline batteries (installed)
- Soft carrying case
- TL75 test leads
- AC 72 detachable clip
- TL 940 mini hook test leads
- Instruction sheet
